Home / Custom Glass / Custom mirrors in Monmouth County

Custom glass · Monmouth County

Custom mirrors in Monmouth County, NJ.

Bathroom, wall and gym mirrors cut to your measurements, edged, and mounted. Based in Oceanport.

What we make

A custom mirror is a mirror cut to a size and shape that fits your wall, rather than a stock size that almost fits. On our custom glass page we list the mirror work we do: wall, bath and gym mirrors, cut to fit and mounted. Common requests include:

  • Vanity mirrors sized to the vanity or the full width of the backsplash, with cutouts where an outlet or light box sits in the wall.
  • Wall-to-wall and floor-to-ceiling mirrors for dressing areas, entryways and small rooms that need more light.
  • Home gym and studio walls, often in several panels with tight joints.
  • Replacement mirrors for an old mirror that has black edges, cracks or chips, matched to the original opening.
  • Cabinet and closet door mirrors cut to an existing door or frame.

Every piece is cut to your measurements. We take sizes to the nearest 1/16″, and holes, notches and radius corners are available, as listed on our custom glass page.

Mirrors in Monmouth County homes

Monmouth County housing covers a wide range. Red Bank, Freehold and the Two River towns like Rumson, Fair Haven and Little Silver include many older homes. Middletown, Holmdel and Colts Neck have a mix of older houses and newer builds and remodels. Shore towns like Long Branch, Asbury Park, Belmar, Spring Lake and Manasquan add condos, apartments and seasonal homes. Each of these affects how a mirror should be measured and mounted.

Older walls are rarely square

In older homes, walls, ceilings and countertops are often out of plumb or out of level. A mirror cut to a perfect rectangle can show an uneven gap along a ceiling or backsplash. When a mirror runs wall to wall or meets a counter, we measure every edge on site instead of assuming the opening is square, and we tell you if a slightly smaller mirror with an even reveal will look better than one forced tight.

Remodels: measure after the finishes are in

If you are remodeling a bath in Middletown or Holmdel, schedule the mirror measure after tile, backsplash and the vanity top are installed. Those finishes set the final opening. The National Glass Association also recommends that mirrors be among the last materials installed on a job, and stored dry and away from chemical fumes until then (NGA).

Condos and shore rentals

For buildings in Long Branch or Asbury Park with elevator, hallway or work-hour rules, tell us when you request a quote. Large one-piece mirrors have to fit through doors, stairwells and elevators, so on some jobs a two-piece mirror with a clean seam is the practical choice. We will flag that from your photos and measurements.

Salt air, steam and black edge

The most common way a bathroom mirror fails is not breaking. It is "black edge," also called desilvering: dark spots or streaks that creep in from the edges as the reflective backing breaks down. Kohler describes moisture as the main cause of desilvering (Kohler). The National Glass Association says mirror edges should not get wet with any liquid, and should be dried immediately if they do (NGA).

That matters near the shore, where humid air is a fact of life in Oceanport, Long Branch, Belmar and other coastal towns, and it matters in any bathroom with a hot shower and a weak exhaust fan. A few habits help a mirror last:

  • Run the fan. Ventilate during and after showers, and wipe condensation off the mirror.
  • Spray the cloth, not the mirror. Cleaner sprayed on the glass runs down to the bottom edge and sits there (NGA; Kohler).
  • Skip ammonia and vinegar cleaners. Both NGA and Kohler warn that they can damage mirror edges and backing. Warm water and a soft lint-free cloth is the NGA's first recommendation.
  • Dry the bottom edge and seams. Water and cleaner tend to collect where a mirror meets a backsplash or another panel.
Tip

If your current mirror has black edges, that damage is in the backing and can't be cleaned off. Replacing the mirror and following the habits above is the fix.

Edges, thickness and mounting

Our custom glass page lists four edge finishes. For mirrors, the usual choices are:

EdgeWhat it looks likeCommon use
Flat polishSquare, glossy edgeFrameless vanity mirrors, wall-to-wall mirrors
Pencil polishSoft, rounded edgeA softer look on smaller mirrors
BevelAn angled border that catches lightClassic framed-look mirrors without a frame
SeamedEdges sanded smooth but not polishedMirrors that go into a frame or channel

Glass thickness on custom pieces runs from 1/8″ to 1/2″. For mounting, a mirror can be held with clips, a J-channel along the bottom, or mirror adhesive, depending on size, wall and look. If adhesive is used, it needs to be compatible with the mirror backing. Mirror makers publish lists of compatible products for this reason (Vitro), and the wrong adhesive or sealant can damage the backing over time.

Check first

Mirrors on doors, or in tub and shower areas, can fall under safety glazing rules. Federal standards for architectural glazing cover glass in doors and in bathtub and shower enclosures (16 CFR 1201), and New Jersey enforces building codes through its Uniform Construction Code (NJ DCA). Tell us where the mirror goes and we will confirm what is required.

How it works

  1. Send sizes or a photo

    Width × height to the nearest 1/16″, the edge you want, and a photo of the wall. A photo of the old mirror beside a tape measure works too.

  2. Get a price

    We reply with a quote for the glass, edgework, holes or cutouts, and installation if you want it.

  3. We measure on site

    For wall-to-wall, multi-panel or install jobs, we confirm every dimension before anything is cut.

  4. Cut, edge and install

    Your mirror is cut and finished to size, then mounted. Delivery and installation are optional, as listed on our custom glass page.

Ready to start? Request a quote and choose "Mirror," or text a photo to (732) 786-4997.

Ready for a quote?

Send measurements or a photo and we’ll reply with next steps.

Questions, answered.

Do you cut mirrors to size in Monmouth County?

Yes. We cut wall, bath and gym mirrors to your measurements and can mount them. We are based in Oceanport and serve towns across Monmouth County, including Long Branch, Belmar, Red Bank, Middletown and Freehold.

How much does a custom mirror cost?

It depends on size, thickness, edge finish, holes or cutouts, and whether you want installation. We do not publish a flat mirror price. Send your sizes or a photo through the quote form and we will reply with a price.

Why does my bathroom mirror have black edges?

Black edge, or desilvering, happens when the reflective backing breaks down, usually from moisture and from cleaners reaching the edges. Kohler names moisture as the main cause, and the National Glass Association advises keeping mirror edges dry and avoiding ammonia or vinegar cleaners. The damage can't be cleaned off, so the usual fix is a replacement mirror.

Can a large mirror be made in more than one piece?

Yes. When a single piece would not fit through a doorway, stairwell or elevator, or would be hard to handle, a multi-panel mirror with tight seams is a common solution. We will suggest where seams should go.

When should I measure for a mirror during a remodel?

After tile, backsplash and the vanity top are installed. Those finishes set the final opening, and the National Glass Association recommends that mirrors be among the last materials installed.

Can you cut around outlets and light boxes?

Yes. Holes, notches and cutouts are available. Mark their exact positions on your sketch, or we will measure them on site.

Serving Monmouth County.

  • Oceanport
  • Long Branch
  • Belmar
  • Asbury Park
  • Red Bank
  • Rumson
  • Fair Haven
  • Little Silver
  • Middletown
  • Holmdel
  • Colts Neck
  • Freehold
  • Spring Lake
  • Manasquan

Reviews

Had glass done by TruePane?

A short Google review helps neighbors in Monmouth and Ocean County find a local glass shop. It takes about a minute.